New Build Electricians in Auckland

Understanding Your New Build

When You Need a New Build Electrician

Call your sparky early. Like, really early. Most people wait until the frame’s up and the roof’s on. By then, half your electrical decisions are already locked in. If the walls close up before the wiring’s in the right places, you’re not just paying for the fix later. You’re paying to rip things open first.

So when should you call? A few obvious moments: you’ve bought your section, your builder’s finalising plans, or your architect’s handed you drawings with nothing electrical on them. Less obvious but just as important: the quote you got feels thin, you’ve got no idea how many power points a bedroom actually needs, or you’re hoping to fit solar, an EV charger, or a heat pump later and you’re not sure what the house needs to be ready for. Either way, the earlier we’re in the room the better. This stuff gets lived with for 30 years.

Our New Build Electrical Services

Here’s how it usually runs. We sit down with your plans and go room by room. Power points, lighting, switchboard location, and anything you want pre-wired for the future. Then we talk to your builder and architect so the electrical plan wraps around the house, not the other way around.

Services we handle on every new build:

• New home wiring (full job, start to finish)
• Switchboard sizing & installation
• LED downlight installation
• Dimmer switches & zoned lighting
• Outdoor & security lighting
• Data & communication cabling
• Smoke alarm installation (to code)
• Heat pump pre-wire & installation
• Ventilation system installation
• Home EV charger installation
• Ceiling fans & exhaust fans
• Security system installation

Once it’s all in and tested, you get a Certificate of Compliance signed off against clause G9 of the NZ Building Code. That’s the piece of paper your council, insurer, and bank will all ask for. Every job, every time. No chasing.

Working With Totally Amped Electrical

New Builds Across Auckland

We work on new builds across all of Auckland. Out in Hobsonville and Hobsonville Point, we’re in and out of townhouses and family homes every month. Massey, Kumeu, Swanson. Mostly subdivisions and standalone builds, switchboard to the last socket. Then you’ve got Waitakere, Titirangi, and Glen Eden, where jobs are more bush and coastal. That changes things. Salt air off the west coast chews through cheap outdoor fittings fast, so we spec gear that’ll actually last.

Up on the North Shore in Glenfield, and through Parnell, Remuera, and Epsom on the city side, we do a lot of higher-spec custom homes. Smart home cabling, zoned lighting, multi-circuit switchboards, the full deal. Local knowledge matters more than people think. Different councils want different things. Different suburbs throw different problems at you. Flood zones mean the switchboard has to sit up high. Townhouses mean tight cable runs and awkward switchboard spots. Coastal means everything outside needs to be rated properly from day one.

What to Expect

Every new build goes the same way. Four steps. No guesswork.

Why Choose Totally Amped Electrical

We’ve been trading since 2009, so there’s not much about an Auckland new build we haven’t seen. Our work’s been featured in NZ House and Garden. Every one of us is fully qualified, and every job we do meets NZ electrical regulations. Residential, commercial, big, small. Doesn’t matter, every job gets the same treatment. Show up when we say we will, get it done right, leave the place clean. If you want Auckland electricians who actually take the stress out of a new build, you’ve found us.

Not building new? We also do electrical renovations, switchboard upgrades, and electrical repairs across Auckland.

When should I bring an electrician into my new build?

Sooner than you think. Ideally before the foundation’s poured, and definitely before the frame goes up. At the design stage we can work through the plans with you and your architect, get the switchboard in the right place, and pre-wire for anything you might want later. Leave it too late and you’re paying to rip walls open for stuff that could’ve been sorted in an afternoon.

Can you pre-wire for solar, EV charging, or a heat pump?

Yeah, and you should. We do it on almost every new build now. Pre-wiring during construction is a fraction of the cost of retrofitting later. Solar gets a solar-ready meter and the right cabling run back to the switchboard. EV chargers get their own dedicated circuit, sized for whatever unit you’re putting in (7kW, 22kW, whichever). Heat pumps just need the switchboard sized to handle the extra draw without tripping breakers. Sort it all at the same time and you’re done.

Do I get a Certificate of Compliance for my new build?

Every time. It’s a legal requirement in New Zealand anyway. Your council will ask for it, your bank will ask for it, and your insurer definitely will. We handle the whole compliance process. You don’t need to chase anyone.

How many power points should I plan for in each room?

Honestly? More than you’d think. The NZ standard is the minimum legal requirement, not a target. Our usual recommendation: double sockets on every living area wall, four to six in the kitchen bench run, two doubles per wall in the bedrooms, and plenty of extras in the garage, laundry, and outside. Adding them now costs almost nothing. Adding them later means cutting walls open, so err on the side of too many.

Can you work with my builder and architect directly?

Of course. Most of our new build work runs that way. We sort timing, inspections, and sign-offs with your builder directly so the electrical side slots in without holding up the rest of the job.